ankara escort çankaya escort Extend parallel to edge? - form•Z Discussion - AutoDesSys Forums

Jump to content


Photo

Extend parallel to edge?


  • Please log in to reply
9 replies to this topic

#1 -andrew-

-andrew-

    Advanced Member

  • Members
  • PipPipPip
  • 192 posts

Posted 01 April 2018 - 01:25 PM

 

Hi,

 

I have a building with a shed roof. I'd like to place a beam between two columns a few inches below the underside of the roof underside plane.

 

I know there are a few ways of doing this, but would like to extend from one column parallel to the roof edge all the way to the other column.

 

extend.JPG

 

Is there a way to do this? Any other suggestions?

 

(Image attached)

 

thanks!


  • Rudolphbop, DarrylVet and Hogardnuck like this

#2 vva

vva

    Advanced Member

  • Members
  • PipPipPip
  • 68 posts
  • LocationBielefeld, Germany

Posted 01 April 2018 - 04:33 PM

hi Andrew,

 

draw a rectangle with "Insert" active onto the first column.

then with the "Reshape" tool extend the rectangle to the second column.

thats it.

 

vva



#3 Des

Des

    Advanced Member

  • Members
  • PipPipPip
  • 425 posts
  • LocationIreland

Posted 02 April 2018 - 04:51 AM

If it was me, I would just use the 3d wall tool with justification set to centre and the width set to whatever you want the thickness of the beam to be.

Draw the line snapping to the centre edge of the column to the other centre edge, type in the height and move it up or down to where ever you want.

 

This is one way and VVA's is another but we all have our preferred methods. That's the great thing about FormZ, there is a lot of choice.

 

 

Des



#4 Martin Malinski

Martin Malinski

    Advanced Member

  • Members
  • PipPipPip
  • 60 posts

Posted 02 April 2018 - 05:38 PM

Or you could use 'reshape>offset segment' ...dragging the segments of the column on the face to make the rectangle for the beam....then use 'Derive>Derive Face' to pull the the beam to length...... ;) 

 

Just another method ;) 

 

Martin



#5 -andrew-

-andrew-

    Advanced Member

  • Members
  • PipPipPip
  • 192 posts

Posted 03 April 2018 - 05:56 AM

Thanks all - 

 

Quick note though - pulling the rectangle out of the first column extends it perpendicular to the column... not parallel to the roof edge.

 

I don't want to eyeball it, either - I know I can manually reshape, but that kind of defeats the purpose.



#6 Martin Malinski

Martin Malinski

    Advanced Member

  • Members
  • PipPipPip
  • 60 posts

Posted 03 April 2018 - 06:52 AM

Oh,

didn't realise from the sketch that the columns were different heights, (sloped roof between columns) -my bad- ....Same quick methods can be used, but push/pull from roof face rather than column. (so perpendicular to roof face) Then just trim length of beam to intersect columns..... (you could do all of this by input dimensions if you wanted)

 

Martin


Edited by Martin Malinski, 03 April 2018 - 06:54 AM.


#7 -andrew-

-andrew-

    Advanced Member

  • Members
  • PipPipPip
  • 192 posts

Posted 13 April 2018 - 07:27 PM

Oh,

didn't realise from the sketch that the columns were different heights, (sloped roof between columns) -my bad- ....Same quick methods can be used, but push/pull from roof face rather than column. (so perpendicular to roof face) Then just trim length of beam to intersect columns..... (you could do all of this by input dimensions if you wanted)

 

Martin

The catch is that I don't want the beam against the roof.



#8 Justin Montoya

Justin Montoya

    Advanced Member

  • Members
  • PipPipPip
  • 461 posts

Posted 17 April 2018 - 11:41 AM

This is the perfect case to use the Guide tool.

 

I would simply snap a guide to the segment you want to be parallel (the roof) and then move it to an appropriate location on the column, or you can draw the new beam against the roof and them move the beam later, there's lots of choices with the flexibility in FormZ.  Then draw a line using the 3d wall tool with the new beam thickness from one column to the other.  Define a height.  Now you'll just need to adjust/extend the ends to penetrate the column and subtract the overlap if you like clean geometry.  It's also easy to adjust your new beam thickness and height, while keeping everything parallel and tight.

 

 

Attached Thumbnails

  • parallel1.JPG
  • parallel2.JPG

Attached Files


  • Martin Malinski likes this

#9 Martin Malinski

Martin Malinski

    Advanced Member

  • Members
  • PipPipPip
  • 60 posts

Posted 17 April 2018 - 04:55 PM

Good solution from Justin.... andrew.... no catch, just to illustrate that there's lots of choices with the flexibility in FormZ... Here's the solution with the method I'd suggested.

 

Created beam profile by dragging cord lines from roof....Just dropped the beam from the roof.... picked bottom face of beam and dragged up to level required to provide gap (creating 2nd object)....deleted 1st beam object. ...viola

 

 

 

Attached Thumbnails

  • 2018-04-17_22-36-08.jpg
  • 2018-04-17_22-38-33.jpg

Edited by Martin Malinski, 17 April 2018 - 05:09 PM.


#10 -andrew-

-andrew-

    Advanced Member

  • Members
  • PipPipPip
  • 192 posts

Posted 19 April 2018 - 07:34 PM

Cool! Thanks guys!

 






0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users