Tech 910 Posted April 7, 2020 We have updated the form•Z Tips and Tricks on the form•Z website (Support->Tips and Tricks). Now searchable and easier to navigate! http://www.formz.com/fzsite1219/manuals/TnT/index.htm#t=Front_Page.htm 3 graham_g, Jaakko and palarsen reacted to this Share this post Link to post Share on other sites
Des 368 Posted April 7, 2020 Excellent! Thanks for that ADS 🙂 Share this post Link to post Share on other sites
jsiggia 91 Posted April 7, 2020 Thank you for giving some attention to this page as I think it was Paul's baby. Will we see new content eventually? Also, the FAQ page would be nice to see again or have I just been missing it? If I recall, it needed a version update last I'd seen. Thanks for reading, Joe Share this post Link to post Share on other sites
Tech 910 Posted April 8, 2020 The content has been updated to be current to formZ v9 and some new items have already been added, We will be adding more over time. We still need to determine how to identify the new additions as they are released. Not to take away from Paul's memory, but to be fair the Tips and Tricks were someone else's "baby". Paul did foster the FAQ section which we are also working on updating. Share this post Link to post Share on other sites
jsiggia 91 Posted April 8, 2020 Thanks for setting me straight Z, I must have been thinking of the FAQ with respect to Paul, and my apologies to the real daddy. Very glad to read your response. I'll spend some more time on the new tips page. Stay well, Joe Share this post Link to post Share on other sites
Jaakko 87 Posted April 8, 2020 Thanks ADS. It looks great. Share this post Link to post Share on other sites
¢hris £und 333 Posted April 8, 2020 Question of the Tips: Am methodically going through the tips and tricks... Good Stuff! Am attempting this one now. http://www.formz.com/fzsite1219/manuals/TnT/index.htm#t=Create_an_Object_Array_along_a_NURB_Surface.htm Am wondering, if there is a way so that for every point along the U dimension, could we space the lines evenly along the V? On my attempt, the spacing between the applied segments are not. Even though, the starting parallel lines were all equidistant. The image here taken in the XY plane, shows that the lengths are different (There is no Y displacement) What I am seeing here could make sense if the control lines were somewhat in the same spacing, being a higher density on the right than the left. but they aren't. The lowest Density of the controls were Nearer the middle, not to the left where the longest resulting curved segment is. The example makes it look like each line is equidistant for every location in the other direction. Am I doing something wrong, or seeing the example wrong.? Thanks! ¢£ Share this post Link to post Share on other sites
Smarttec 36 Posted April 14, 2020 On 4/8/2020 at 11:21 AM, Tech said: The content has been updated to be current to formZ v9 and some new items have already been added, We will be adding more over time. We still need to determine how to identify the new additions as they are released. Not to take away from Paul's memory, but to be fair the Tips and Tricks were someone else's "baby". Paul did foster the FAQ section which we are also working on updating. Yes it was Matthew Holewinski who did most of these. Share this post Link to post Share on other sites
jsiggia 91 Posted April 14, 2020 Thank you Smarttec! Share this post Link to post Share on other sites
AsOne 432 Posted April 15, 2020 Awesome. I will take a look! Share this post Link to post Share on other sites
Hugo 125 Posted April 15, 2020 very nice to have this. +1 tech Share this post Link to post Share on other sites
tbgb 1 Posted May 25, 2020 These are very helpful, thanks so much Share this post Link to post Share on other sites